| Section |
Code |
Description |
Application |
 |
A170 |
Drip Fascia
170mm girth
65mm deep fascia |
Fitted to roof edge for drainage into gutter. Used on edge detailing which requires a smaller drip trim. |
 |
A200 |
Drip Fascia
200mm girth
90mm deep fascia |
Fitted to roof edge for drainage into gutter. All edge detailing where drainage is required. |
 |
A250 |
Drip Fascia
250mm girth
140mm deep fascia |
Roof edge detail to cover insulation. Deep fascia to allow gutter penetration. |
 |
B230 |
Raised edge trim
Check kerb 230mm girth
105mm fascia depth |
Flat roof edge detail to prevent water run off. |
 |
B260 |
Raised edge trim
260mm girth
125mm fascia depth |
Roof edge detail. Compatible with Universal external covers. |
 |
B300 |
Raised Edge Trim
300 / 330mm girth
175mm Fascia Depth |
Roof edge detail compatible with external covers. |
 |
C100 |
Simulated lead wall cover flashing
100mm vertical cover
35mm wall penetration |
Replaces traditional lead flashing. With integral moisture trap return, self secures into brickwork. |
 |
C100
Std |
Simulated lead wall cover flashing
100mm vertical cover
35mm wall penetration |
As above but without integral moisture trap. |
 |
D260 |
Wall fillet
260mm girth
90mm & 110mm flanges
120/140mm upstand height |
For use against abutting walls. Gutter lining. Provides expansion jointed and cross roof ventilation. |
 |
E280 |
Expansion Joint
300mm girth
100mm flanges
50mm height |
Expansion joint for use on large roof areas with rigid systems or to cover existing ex joints on refurb. May also be used to control roof drainage. |
 |
E280 |
Top hat section
|
For use with simulated lead or copper sheathing systems to give the appearance of a rolled joint. |
 |
F300
|
Flat Flashing
Up to 1350mm wide
Rolls from 24m long
300mm standard width |
Flat section for use as continuous flashing under slates at roof junction. Gutter lining. |
 |
G180
|
Expansion Joint
180mm girth
160mm wide
15mm height |
Expansion joint for use on large roof areas. May also be used to control roof drainage. |
 |
C1
|
Universal external corner.
Hot press moulded GRP pre formed corner. |
For use with Sections A200 and B260. Provides pre-formed RH and LH corners. |
 |
C2
|
Fillet to trim
RH and LH mouldings |
For use at junction of flat roof and abutting wall. Compatible with sec. D260, A200, B260. |
 |
C3
|
Fillet corners
Internal and extern |
Chimney corners. Compatible with D260 only. |
 |
C4
|
Universal internal corner.
|
For use with A200 and B260. |
 |
C5
|
Expansion joint closure
|
For use with E280 to seal end of expansion joint to roof deck. |
 |
CE300
|
Continuous eaves course
Colour slate grey. Non binding finish |
For use in place of first eaves slate course to provide initial lap. |
 |
N/A
|
AT175INT. 2.4m 175mm Girth Angle Trim Bonding Surface on Inside
|
|
|
N/A
|
AT175EX. 2.4m 175mm Girth Angle Trim. Bonding Surface on Outside
|
|
 |
N/A
|
S500 Soffit Trim. 10" Fascia Soffit Trim. Used to encapsulate concrete deck edges.
|
|